Working Logical Oscilloscope

Working storage oscilloscope, made to work with logic elements in the game, and view the structure of various signals of different frequencies. [hr[/hr Instructions Quick Start: 1. Turn on the oscilloscope by pressing the large red button in the upper left corner; 2. Apply a variable signal to input #1 or #2; 3. Press the auto-tuning button - yellow button, located at the top not far from the power button; 4. Wait about 15-20 seconds until the auto-tuning is complete; 5. Everything is ready, you can observe the graphs in basic mode. 6. To switch the mode to sinusoidal, press the blue (cyan) button, and run auto-tuning again. Also in this mode you can work with two signals at once by combining them into one, using the dark green button next to the blue (cyan) button; 7. For advanced viewing, press the blue button to activate the auxiliary grid, located in the lower right corner of the first panel, next to it there will be 3 black buttons; All notations and functions. (Numbers with A added at the end stand for indicators, B for inputs). Main control buttons 1. Big red button - Responsible for turning on the oscilloscope; 2. Blue button - Enables and disables the extra bar display; 3. Green (left) button - Switches the updating of the period counter from the basic to the signal from the input (not recommended when working with high-frequency signals); 4. White button - Updates the period counter, holding it down for 1.5 seconds will lock the automatic update (can be locked during automatic setup); 5. Red button - Locks the period counter; 6. Yellow button - Auto-tuning (input signal required); 7. Dark gray (top) button - Multiplies the signal by 2 (provided the second common input signal mode is enabled); 8. Gray (bottom) button - Enables the second signal mode, for long signals; 9. Cyan button - Switches modes from square to sinusoidal; 10. Dark green (right) button - Sums two sine waves into one; 11. Orange button - Condenses the output sinusoidal signal; 12. Black button - Switches the operating input (can be mixed in sine mode for the sum of two sines); [hr[/hr [hr[/hr 1A. The first two numbers (in the upper left corner) - Number of positive ticks in the signal (N/16); 2A. Second two numbers (in the upper right corner) - Number of negative ticks in the signal (N/16); 3A. Analog frequency meter (0-20Hz, +-0.65Hz); 4A. Digital frequency meter (0-20Hz, +-1Hz); [hr[/hr (Also activates the advanced information display mode) [hr[/hr 13. Large white button - Overwrites the storage device; 14. Orange button next to the white button - Blocks automatic refresh of the storage device; 5A. White light - Memory operation; 6A. Green indicator - Record positive ticks; 7A. Red indicator - recording of negative ticks; [hr[/hr [hr[/hr 1B. Entry #1; 14. Large yellow button - Switching input modes #1: 8A. Green - All 4 gates must be connected. 9A. Yellow - At least 1 gate must be connected. 10A. Orange - All gates on the input will be connected via XOR. 11A. Red - All input gates will be connected via NAND; 2B. Input #2; [hr[/hr 15. Large blue button - Lowers the frequency on the frequency generator; 16. Big red button - Increases the frequency on the frequency generator; 12A3B. Input #3 - Frequency generator output; [hr[/hr 13A. Blue lamp - Indicator of the first input mode; 14A. Orange lamp - Indicator of the second input mode; [hr[/hr 15A. Debug Ports; [hr[/hr 16A. Current version; [hr[/hr Notes and Tips With the help of the version indicator you can compare the current version with the current one (at the end of the description); In case of stable signals, it is recommended to disable the automatic update of the period counter, as it may cause interference (hold down the white top button for 1.5 seconds); At sharp change of signal twice, the memory can write wrong values, you can find out it by adding 2 numbers, for example 1+F(15)[/hr Authors and Helpers Author Idea: Yushiri Help with logic: H O N D A Photoshop: dasdel [hr[/hr Tags Oscilloscope, Memorizing, Storage, Gray, Logic, Sinusoidal, Quadratic. Current Version 2.3.0.0